What's your project topic?
Electrical Engineering Project Topics & Research Materials | Final Year Research Project Topics With Free Chapter One
-
1. APPLICATION OF FUZZY LOGIC TECHNIQUE FOR POWER LOSS REDUCTION IN THE NIGERIA 330...
» ABSTRACT` To improve the overall efficiency of the power system, the performance of transmission system must be improved. Some of the vital ways of achieving this objective is by reducing power losses in the system and also improving voltage profile. An important method of controlling bus voltage is by shunt capacitor banks in the transmission substations. The capacitor absorbs reactive power flow...Continue Reading »
Item Type: Project Material | 86 pages | 5,330 engagements |
-
2. COMPARATIVE ANALYSIS OF A TRANSFER FIELD MACHINE AND AN INDUCTION MACHINE
» ABSTRACT This work presents a comparative analysis of a transfer field machine (TFM) and a polyp phase induction machine (IM) . Although the two machines belong to two different classes of machine and quite different in physical configuration , yet both display similar torque – Slip characteristics. However, the synchronous speed of the transfer field machine is ωo/2, that is, one half th...Continue Reading »
Item Type: Project Material | 65 pages | 4,505 engagements |
-
3. DEVELOPMENT OF A POWER MANAGEMENT ALGORITHM FOR ELECTRICAL POWER NETWORK
» ABSTRACT This project work is aimed at developing an efficient Algorithm for the management of Electric Power network using fuzzy logic. The fuzzy logic model functions as a system operator in making decision for load shedding and transfer switching. The new technique uses the system data frequency variation, load variation and voltage variation and the experience of the system operators to for...Continue Reading »
Item Type: Project Material | 65 pages | 5,455 engagements |
-
4. RELIABILITY EVALUATION OF SECONDARY DISTRIBUTION SYSTEM IN NIGERIA
» ABSTRACT A power system is set up basically to meet the demands of the customers. However, interruptions which are largely unavoidable contribute to the unavailability of power and thus prevent power system from achieving this. In most cases, it is the sustained interruptions that greatly affect both the utility company and its customers. Hence, it is necessary to find means of determining w...Continue Reading »
Item Type: Project Material | 65 pages | 5,635 engagements |
-
5. DESIGN AND FABRICATION OF MINI COPULA FURNACE AND AN ATOMIZER FOR THE PRODUCTION...
» ABSTRACT This research is centered on the design and fabrication of copula furnace and atomizer for the production aluminium powder metal with the available material.0.4kg of refined coke was chosen as the basis for material and energy balance calculations and the design calculations performed from whose values are used to produce the design drawings. Mild steel was used for the internal linings o...Continue Reading »
Item Type: Project Material | 65 pages | 4,320 engagements |
-
6. MICROCONTROLLER BASE DOT MATRIX ADVERT DISPLAY
» CHAPTER ONE INTRODUCTION The purpose of this project is to produce a narrative description of the design and construction of a microcontroller based dot matrix advert display. Firstly computer aided design is the modeling of physical system on Computers allowing both interactive and automatic analysis of design variant and the expression of design in a form suitable for manufacturing. This ...Continue Reading »
Item Type: Project Material | 65 pages | 5,880 engagements |
-
7. CONSTRUCTION OF UNINTERRUPTIBLE POWER SUPPLY
» ABSTRACT Uninterruptible power supplies (UPS) are used to provide power when regular utility power is unavailable. Although they are commonly used for providing power in remote locations or emergencies, this is not because they are the same as auxiliary power units, emergency power units or standby generators.Unlike the aforementioned power sources, UPS provides an immediate and continuous s...Continue Reading »
Item Type: Project Material | 65 pages | 0 engagements |
-
8. CONSTRUCTION OF 1KVA INVERTER USING SOLAR PANEL
» Abstract The project is a construction of inverter using solar panel and its operation. The problems of power lead to the aims and construction of the inverter. This project comprises of four chapters, chapter one deal with the introduction and background of the project. Chapter review of related literature of the project, chapter three construction testing and observation and finally chapter four...Continue Reading »
Item Type: Project Material | 65 pages | 11,104 engagements |
-
9. POWER SUPPLY AND USE IN GYEL DISTRICT JOS
» ABSTRACT The importance of power supply to any economy cannot be overemphasized. It the pivot on which the economic, industrial and technological development of any nation is hinged upon. This study was carried out to assess the state of power supply and use in Gyel District of Jos South Local Government Area of Plateau State. Four communities were selected to constitute the sample population...Continue Reading »
Item Type: Project Material | 65 pages | 4,912 engagements |
-
10. LINE LOSSES MINIMIZATION IN ELECTRICAL POWER NETWORK USING PARTICLE SWARM OPTIMI...
» ABSTRACT Energy is a basic necessity for the economic development of a nation. There are different forms of energy, but the most important form is the electrical energy. A modern and civilized society is so much dependent on the use of electrical energy. Activities relating to the generation, transmission and distribution of electrical energy have to be given the highest priority in the national p...Continue Reading »
Item Type: Project Material | 60 pages | 6,182 engagements |
-
11. IMPLEMENTATION OF UNIFIED POWER FLOW CONTROLLER (UPFC) FOR IMPROVEMENT OF VOLTAG...
» ABSTRACT As the demand of electricity from an already congested network increases, ensuring voltage stability across the network becomes challenging. One approach in ensuring system stability is to attain system redundancy but their economic and ecological limitations to this. A more cost effective means would involve the use of existing network component and incorporate less expensive scheme and ...Continue Reading »
Item Type: Project Material | 65 pages | 5,318 engagements |
-
12. IMPLEMENTATION OF AN AUTOMATIC FIRE DETECTION AND ALARM SYSTEM
» INTRODUCTION The Voice prompt fire detector and extinguisher are considered better alternatives to traditional audible alarms because a voice is typically less likely to instill panic, and the voice feature can be used to give specific instructions, for specific situations. They not only let everyone when an emergency arises but they also inform the people of certain measures to take to avoid conf...Continue Reading »
Item Type: Project Material | 65 pages | 6,352 engagements |
-
13. DEVELOPMENT OF A NOVEL ALGORITHM FOR VOLTAGE STABILITY ASSESSMENT USING SYNCHROP...
» ABSTRACT As a result of recent increases in demand for electric power, utility transmission systems have been forced to operate under stressful conditions, often close to instability limits. Efforts to construct new transmission lines or enlarge networks are limited due to economic and environmental constraints. According to U.S. Department of Energy, since 1982, the growth in peak demand for elec...Continue Reading »
Item Type: Project Material | 65 pages | 4,423 engagements |
-
14. DESIGN AND FABRICATION OF FREEZE DRYER
» ABSTRACT Water is responsible for changes in the physical, chemical and/or biological characteristics of foods. It is an important component of all biological or living systems. In fresh foods, the percentage of water varies from 60% to more than 90% (Davide and Salvatore, 2012). Water content in foodstuffs during processing, storage and distribution may lead to deterioration of aroma and degradat...Continue Reading »
Item Type: Project Material | 65 pages | 5,324 engagements |
-
15. DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE REGULATOR
» ABSTRACT This project proposes a new type of voltage regulator based on single phase converter otherwise known as transformerless AVR that compensates wide range voltage variations. This is not only capable of compensating variations at a much higher bandwidth but also does not experience mechanical wear down and is cost effective. The proposed device employs a pulse width modulation (PWM) z sourc...Continue Reading »
Item Type: Project Material | 65 pages | 10,117 engagements |
-
16. A TECHNICAL REPORT ON STUDENT INDUSTRIAL WORK EXPERIENCE SCHEME AT THE TRANSMISS...
» ABSTRACT SIWES (Student Industrial Work Experience Scheme) was established by the Federal Republic of Nigeria in the year 1973 to cater for the problem of underdevelopment and skill acquisition and also to impact practical knowledge and skills to students, thus bridging the gap between theoretical knowledge and practical. The Scheme exposes students to industry based skills necessary for a smooth ...Continue Reading »
Item Type: Project Material | 65 pages | 8,400 engagements |
-
17. A SEMINAR REPORT ON STREET LIGHT INSTALLATION
» ABSTRACT This seminar report is based on the reality of street lighting, kiosk, street light continuity, types of connections in street lighting and its major advantages and disadvantages. Street light installation system is not only easiest but also the powerful technique. The main consideration is the present field technologies which are automation, power consumption and cost effectiveness power...Continue Reading »
Item Type: Project Material | 65 pages | 6,360 engagements |
-
18. A SEMINAR REPORT ON CIRCUIT BREAKERS
» ABSTRACT This contribution provides an overview on the common on site test methods to ensure the safe and reliable operation of circuit breakers used in high and medium voltage power systems. Failures on circuit breakers can generally be ascribed to defects in one or more of the three main components: The operating mechanism incl. mechanical linkage, the electrical control circuits and the compone...Continue Reading »
Item Type: Project Material | 65 pages | 6,820 engagements |
-
19. A SEMINAR ON THE POTENTIALS OF THE MINI-GRID AS A DRIVER OF THE NIGERIAN ECONOMY
» ABSTRACT Nigeria is a country with a population of over 170 million; it is rightly the most populous country in Africa and the eighth most populous country in the world. According to the United Nations, one in six Africans is Nigerian. It is a regional power, listed among the “Next Eleven” economies, and a member of the Commonwealth of Nations. Nigeria’s Gross Domestic Product (GDP) was rev...Continue Reading »
Item Type: Project Material | 65 pages | 4,739 engagements |
-
20. DESIGN AND CONSTRUCTION OF A 2KVA POWER INVERTER
» CHAPTER ONE INTRODUCTION BACKGROUND OF THE PROJECT Electrical/Electronic Engineering is a very important element that cannot be neglected in the society as it is deeply sewn into the fabric of the society. It is an important element in homes to power household devices like electric bulbs, electric cooker, refrigerator, television set, etc. It also finds applications in various work places/offices ...Continue Reading »
Item Type: Project Material | 65 pages | 7,317 engagements |
-
21. DESIGN AND CONSTRUCTION OF A 1KVA MOBILE SOLAR GENERATOR
» CHAPTER ONE INTRODUCTION 1.1 Preamble A power inverter, or inverter, is an electronic device or circuitry that changes direct current (DC) to alternating current (AC). (The Authoritative, 2000). The input voltage, output voltage and frequency, and overall power handling depend on the design of the specific device or circuitry. The inverter does not produce any power; the power is provided by the D...Continue Reading »
Item Type: Project Material | 65 pages | 8,592 engagements |
-
22. DESIGN AND INSTALLATION OF A REMOTE CONTROLLED SYSTEM
» AHAPTER ONE INTRODUCTION OBJECTIVE OF PROJECT The need for a remote control alert system that can control domestic appliances and various lighting points and sockets has often been a concern for users. At times users find it inconvenient and time consuming to go around turning their appliances on or off each time there is power outage or each time they are leaving the house for work. It has al...Continue Reading »
Item Type: Project Material | 65 pages | 5,231 engagements |
-
23. INDUSTRIAL BATCH COUNTER
» CHAPTER ONE INTRODUCTION The industrial batch counter is an electronic and electrical device that handles the counting and controls the flow of individuals using an automated slide door that allows access only when the administrator permits. The technique involved in the design is a simple sensor unit that opens and closes the door when someone obstructs the light path. These parameters can be ...Continue Reading »
Item Type: Project Material | 65 pages | 4,982 engagements |
-
24. DESIGN AND CONSTRUCTION OF AN ELETRONIC DIGITAL DISPLAY SYSTEM (MOVING MESSAGE D...
» Chapter one INTRODUCTION 1.1 Background of the study Electronic digital display system as used in this reports refers to a sign that uses electronic hardware and software to display its copy, messages or images. Also, a sign utilizing a fixed light source to provide a message in text, images pictures, and / or symbols that may appear to move or may appear as on/off messages. Thi...Continue Reading »
Item Type: Project Material | 65 pages | 8,028 engagements |
-
25. DESIGN AND CONSTRUCTION OF A METAL DETECTOR
» ABSTRACT The project work titled Design and construction of a metal detector. When fully design and implemented would be able to detect any metallic material that is passing or coming close. This function would serve as a security check for dangerous metallic material as an alarm. Going by the sophisticated means of armed rubbers adopt these days in the breaking into bank supermarkets offices and ...Continue Reading »
Item Type: Project Material | 65 pages | 12,817 engagements |
Searching makes things a lot easier.. Search for what you are looking for